High-Precision and Multi-Function Ultrasonic Thickness Gauge PM5 Gen2
Brief Introduction:
The iqualitrol PM5 Gen2 thickness gauge is an advanced ultrasonic thickness gauge with a variety of standard measurement functions and special feature options.
This portable thickness gauge uses different frequencies and different types of single crystal probes to meet most measurement requirements.
With wide measurement range, it can accurately measure thickness range from 0.15mm thin steel plates to tens of meters long steel rods, and even tens of microns of ultra thin paint layers.
The full-featured PM5 Gen2 can be used for almost all thickness measurement applications.
Technical Specifications:
| Measurement Principles and Parameters | ||
| Measurement Mode |
P-E(Pulse-Echo Method):Measure the time interval between initial pulse and the first back-wall echo. I-E(Interface Wave-Echo Method):Measure the time interval between the delay block echo and the first back-wall echo. I-E-E(Echo-Echo Method):Measure the time interval between two consecutive back- wall echoes. I-ME(Multiple Echo Method):Measure the time interval between multiple backwall echoes. E-EV(Double Echo Verification):In E-EV mode,three echoes are required. COAT Mode(Optional):This is coating specific measurement mode. OXIDE Mode(Optional):Specially designed to measure the thickness of the oxide layer on the inner wall of boiler tube. PELR Mode (Optional):When the material thickness exceeds the measuring range, this mode needs to be selected. |
|
| Probe Types | Standard delivery single D15A probe, options: delay line probes, contact probes, protective film probes, pen type probes, water immersion probes and high temperature probes. | |
| Calibration Methods | Zero calibration type, calibrate sound velocity, one-point calibration, two-point calibration, set sound velocity, material sound velocity table. | |
| Indication Error |
±0.01 ±0.05 |
H ≤ 3mm 10mm ≤ H |
| Note: H represents the thickness of the tested material. | ||
| Thickness Range |
0.01 mm-38 meters, depending on the material, probe surface conditions, temperature and selected configuration. 0.15mm-30mm (standard D15A probe, steel) |
|
| Material Sound Velocity Range | 310-18699m/s, the sound velocity can be calculated for objects with known thickness. | |
|
Resolution |
Low Resolution:0.1mm Standard Resolution:0.01mm High Resolution:0.001mm Ultra High Resolution(Optional):0.0001mm or 0.1um(I-ME) |
|
| General Specifications: | ||
| Working Language | English | |
| Measurement Units | mm, inch, μm, mil | |
| Temperature Range | -10℃-50℃ | |
| Instrument Housing | Impact-resistant, waterproof, gasketed casing, interface seal on the casing, designed to IP67 standards. | |
| Size | 153mm×76mm×37mm(H×W×D) | |
| Weight | 280g including batteries | |
| Power | 2 AA size batteries, operating time is more than 24 hours. | |
| Display | ||
| Display | 2.4 inch (320*240 dot matrix)TFT color display LCD screen | |
| Rectification Mode | Radio frequency, Inverter radio frequency, full wave, positive half wave, negative half wave. | |
| View Mode | A Scan mode, B Scan mode, value mode, normal, maximum value capture, difference value, over-limit alarm. |
|
| Built-in Data Logger Option | ||
| Data Logger | Identify, store, recall, clear, and transmit thickness readings, waveform images, and instrument configuration etc.by a standard USB port. | |
| Capacity | Store 100,000 thickness values and 400 parameter configuration files, equipped with host computer software and USB disk. | |
| Communication in Real Time Option | The host computer controls the instrument and transmits thickness values, waveforms and parameters in real time, including the host computer measurement software. suitable for online measurement and secondary development. |
|
| Multi-Channel Option | Includes host computer multi-channel measurement software, mainly used for automated thickness measurement. | |
Contact Person: Mr. Raymond Chung
Tel: 86-13711988687
Fax: 86-769-22784276
| Factory Address:No. 88 Jiaolian Yiheng Rd, Wanjiang District, Dongguan, China, 523046 | |
| Sales office:Room 301, Building No.1, No. 2 Jiaolian Yiheng Rd, Wanjiang District, Dongguan, China, 523046 | |
| +86--13711988687 | |
| sales@iqualitrol.com | |
